Howto: Removing a disk from a VM - howto identy the right disk?

From time to time, we need to remove disks from a VM. If there's only two or three disks attached to the VM, it's typically not a problem figuring out which one to remove e.g. if the disks have different sizes. But if you have seven or eight disks and they are the same size, then it's a bit more tricky - let's say if you're asked to remove the 'E-drive'. Under 'Edit Settings' for the VM, the disks only have a number which does not necessarily correspond with anything within the VM.

So how to identify exactly which disk that corresponds with a given volume within Windows?

The match can be made by looking at the SCSI target ID for the disk - this can be identified both in WIndows and under 'Edit settings' for the VM (A VM can have four SCSI controllers with up to 15 disks on each controller, so a maximum of 60 disks per VM).

To identify SCSI target ID within the VM:

Go to Computer Management -> Disk Management

Right click a disk and choose Properties

On the General tab you will see the Bus number (SCSI controller) and the Target ID (SCSI target ID), note the number - in this case below the ID is 4.

To identify SCSI target ID from the VI client:

Now go to 'Edit Settings' for the VM under and locate the disk with the corresponding target ID (see Virtual Device Node for the disk). Make sure the that the controller number and SCSI ID is the same. In this case it is Hard Disk 5 that have SCSI ID 4.

Shut down the VM to remove the disk.

VMware: How to check HBA firmware version without rebooting ESX host

I need to find out witch firmware version is running on my HBA without rebooting the ESX host.. I thought this was possible by GUI but couldn’t find it, so I decided to check this by console. Give the following commands:

Navigate to:
- cd proc/scsi/qla or lpfc820
- ls –lia
To view the HBA information:
- cat 6
- cat 7

Result:

Configuring iSCSI for vSphere 5

Configuring a software iSCSI initiator for ESXi 5.0 is a relatively simple operation. This quick guide assumes that you have already configured an iSCSI target and published it on the network.

For inspiration, have a look at this VMware KB

Create a new vSwitch (Configuration -> Networking -> Add Networking) and add a VMkernel. Configure it with an IP address. 

Go to Storage adapters and click "Add" to add a software iSCSI adapter if it does not exist already.

Once added, right click the software initiator and choose "properties". 

Go to Network Configuration tab and click "Add".

Choose the vSwitch/VMkernel that you created above.

Go ot Dynamic Discovery tab and click "Add" to add an iSCSI target

You will be prompted to input IP address of the iSCSI target, just leave port 3260 as default unless you have configured it differently on your target.

Go to Configuration -> Storage and click "Add storage". Click DISK/LUN and next. If everything has been done correctly, you be able to see your published iSCSI target and can then add and format it with the new VMFS5 file system, uh lala!

iSCSI on a Windows box with Starwind

If you want to run shared storage in e.g. a test setup, then Starwind's iSCSI application can be recommended. Earlier, I have tried Openfiler (iSCSI in a linux distro VM) which works fine, It's not too complicated to configure, but still it's much easier with Starwind iSCSI in a Windows environment. The application is free but there's a 2 TB storage limit.

Download Starwind Free here.

Starwind installation guide. It's easy to install, just go next next done. Load the serial key, connect to the localhost (user: test, pw: test), add a new device, and then follow install guide page pp 5.

For a guide on how to configure iSCSI in ESX 3 and 4, click here

A typical test setup could be one physcial host with 8 GB of memory and one quad core cpu. Check vm-help.com for a list of compatible whitebox ESX hardware.

From ESX 4 it's possible to run ESX as a VM within an ESX. Even VMotion will work (go to vcritical.com for a demonstration). And if you have a VM with an iSCSI target running on it, then you have a full enterprise setup running on one box.